Debian-news is about one simple thing - news about Debian GNU/Linux and the top free distributions based on Debian GNU/Linux.


 

Changes for Squeeze in Debian Installer

Normally an overview of changes is given when a new version of Debian Installer is released. However, a release has been in preparation for something like the past six months and it is currently unclear whether one will happen before or after the next ice age.

So here’s an overview of the more important changes in D-I since Lenny that
are available in current daily and weekly built images.

Note that for different reasons there are issues with daily/weekly images
for various architectures. The images for i386, amd64, armel and sparc are
fairly reliable. Images for other architectures may at times be either
outdated, unavailable or broken.

Most of the changes listed below are documented in the development version
of the Installation Guide [1].

Installation of recommended packages
————————————
For Lenny and earlier releases Debian Installer did not install Recommends.
This has been changed for Squeeze and D-I will now install recommended
packages by default.

There is an option to configure APT to not install Recommends by default
(from the boot prompt or using preseeding). This option is intended only
for expert users who know what the consequences are of not installing
Recommends and who have the experience/skills needed to cherry-pick any
desired Recommends after the installation has been completed.

The installer makes a few specific exceptions to the general configuration
by either always or never installing the Recommends of specific packages
in cases where following the general setting gives undesired results.

Changes in selection of language/country/locale
———————————————–
The “localechooser” component of the installer has received some love. This
component combines selection of three values:
- language
- location (country)
- locale

There have been improvements to make the selection of location and locale
less interdependent and at the same time more flexible. The dialogs have
been improved to provide better guidance.

When selecting a location, users should select the “country where they
live” as the selected location determines the local time zone the
installed system will use. New is that for languages for which multiple
locales are available, the installer will then (if needed) ask which
locale the user prefers.

So, using the Squeeze installer it is now possible during default
installations to say for example “I want to use English as language, I
live in Germany (and thus want CET as time zone), and prefer en_GB.UTF-8
as my system locale”.

Selection of additional locales to be generated (including legacy locales)
is still only possible when installing in expert mode (using medium or low
debconf priority).

More flexible preseeding of language/country/locale
—————————————————
For Lenny and earlier releases it was only possible to preseed “locale”,
which would be parsed and also set language and country. Because of this
not all possible (and valid) combinations of language/country/locale could
be selected using preseeding.

This method of preseeding localization values is still supported, but it is
now also possible to preseed language, country and locale as separate
values which does make all combinations possible.

Improved mirror selection
————————-
The main improvements are better support for installing oldstable and
archived releases from archive.debian.org.

Other changes:
* only displays available releases (in case of partial mirrors)
* normally displays both the codename and the suite of available releases
* warns if the default release is not available (instead of silently
falling back to a different release)
* improved checks that the selected mirror is consistent

Option to select the “UTC” time zone
————————————
This new option is only available in expert mode (or more exact: when
installing at medium or low debconf priority).

Changes in the partitioner (partman)
————————————
* support for using the ext4 file system
* setting up RAID, LVM and crypto is simplified: it’s no longer required
to first set the correct usage for a partition

Other changes
————-
* installed systems get console-setup (instead of console-tools plus
console-data)
* [x86] installs grub-pc (grub2) by default
* [armel] support for Marvell’s Kirkwood platform:
– QNAP TS-110, TS-119, TS-210, TS-219 and TS-219P [2]
– Marvell SheevaPlug [3]
– Marvell OpenRD-Base and OpenRD-Client
* [armel] support for Intel Storage System SS4000-E
* compatibility support for installing Lenny
Note that as there is no updated kernel in Lenny, the installed system
will still get the 2.6.26 kernel.

Cheers,
Frans Pop

(This mail is sent on personal title, not on behalf on the D-I team.)

[1] http://d-i.alioth.debian.org/manual/
[2] http://www.cyrius.com/debian/kirkwood/qnap/ts-219/
[3] http://www.cyrius.com/debian/kirkwood/sheevaplug/

One Response to “Changes for Squeeze in Debian Installer” »

  1. Pingback by Changes for Squeeze in Debian Installer | Debian-News.net - Your … | Just linux! — January 9, 2010 @ 1:35 am

    [...] The rest is here: Changes for Squeeze in Debian Installer | Debian-News.net – Your … [...]

RSS feed for comments on this post. TrackBack URI

Leave a comment

Leave a Reply

Your email address will not be published. Required fields are marked *


*

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>

Debian-News is not related to the Debian Project.
All logos and trademarks on this site are property of their respective owners.